Log in Account Management. Video Management. Terms of Use Disclaimer The information provided in this article and others on support. Information Issue. You cannot pan, tilt, zoom, or access the menu for a camera. Possible causes include the following: A mismatch of the baud rate, parity, protocol, or address between the encoder and the camera; camera hardware failure; loose or mismatched cabling; encoder hardware failure; the camera is not configured as a PTZ camera in the Endura system; the user account in use does not have the permission to PTZ the camera; or the PTZ priority service on the system manager is not responding.
Click on the Login link in the upper-right corner. Log in with user name admin and password admin. Once the live view page returns, you should see PTZ controls on the side of the page. Attempt to move the camera using those controls. If it responds, skip to Section V.
Otherwise, proceed to Section II. Once the camera starts back up, it should display a diagnostic message similar to Figure 1, below: FIGURE 1 Camera power-on self test In Figure 1, above, the camera is set to baud, no parity, 8 data bits, and 1 stop bit Next, verify the baud rate, parity, data bits, and stop bit settings also match on the encoder using the following steps: Open the WS program.
Right-click on the encoder channel you wish to modify and choose Modify settings. Click on the View hierarchy button in the upper-right corner of the window. Click on the encoder the camera is attached to in the list and choose Modify settings, as shown in Figure 2, below: FIGURE 2 Device hierarchy Verify that the baud rate, parity, data-bit, and stop-bit settings for the encoder match the settings shown by the camera, as shown in Figure 3, below.
The Tx- terminal on the encoder should connect to the Rx- terminal on the camera. Analog systems use wired configuration or a wired transmitter. Operating such a device requires you to run a wire between the monitor and the device, together with a coaxial cable used to send data. Analog systems cannot be accessed remotely or are distance-limited.
Every property is unique, and different homes require different styles of cameras, with different lenses. There is no device that perfectly fits all scenarios or is right for everyone. Pelco is one company that advises customers throughout the entire selection and set-up process. This usually depends on the owner's preference and location of the safety device.
Some of the Pelco home safety devices have fixed lenses that capture sharp images but are not capable of adjusting how the safety device focuses. You can always point the camera in a different direction when your hand is on it, but what you see through it is what you get.
Pelco home safety devices have lenses that allow for a wide range of adjustment, all carrying varifocal lenses that provide you with the ability to manually configure the focus and zoom on the device, thus helping you to get the view you seek. After reading this page and testing the camera with the Analyzer software, you should be able to understand the ease of using the Pelco-D protocol, and control any Pelco-D cameras in five minutes' time.
This page will explain the following topics in details: 1 The format of Pelco-D 2 How to calculate the checksum byte by using Analyzer 3 Pelco-D command string examples 4 How to use Analyzer to control the Pelco-D cameras 5 Have fun playing with Analyzer and Pelco-D cameras After reading this page and testing the camera with the Analyzer software , you should be able to understand the ease of using the Pelco-D protocol, and control any Pelco-D cameras in five minutes' time.
You will then get the result of '44' Step 2: Change Operator to ',Mod', and key in the previous result '44' and modulo parameter '' in the 'Input operands' box, remember to add ',' after each byte of data. Audio recording is the icing on the cake. It is designed for those users who demand an easy-to-operate, yet innovative DVR.
The DX features built-in video motion detection, alarm-based recording, and relay output controls. Free download pelco dx export viewer avi mp4 Files at Software Informer. Click New Var button to add checksum.
This is the Byte 7. The default address is 1. Edit Command 1, Command 2, Data 1 and Data 2 according to Pelco D commands Click Send button, the checksum will be added to the end of send data automatically If you check the option Add to List, you will see the command is also added to the Send Data List. Follow the step 7, you can have Pelco D command list in minutes. For example: Set 90 degree for Pan position According to the instruction of Pelco D protocol manual, Pan position is given in hundredths of a degree and has a range from 0 to decimal.
Please contact us if your protocol is not list above. For individual, one PTZ Controller registration code could be installed up to 3 computers, which belongs to the same user. For company, you have to buy registration code for every computer. PTZ Controller software is built with the latest. Net Framework.
0コメント